|
|
|
|
|
|
|
|
|
|
|
|
|
* This item was taken out from the Tamiya Car Kit, No Tamiya Original Retail Packing
|
* This item was taken out from the Tamiya Car Kit, No Tamiya Original Packing
|
* This item was taken out from the Tamiya Car Kit, No Tamiya Original Packing
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
* This item was taken out from the Tamiya Car Kit, No Tamiya Original Packing.
|
* This item was taken out from the Tamiya Car Kit, No Tamiya Original Packing.
|
* This item was taken out from the Tamiya Car Kit, No Tamiya Original Retail Packing
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Replace the standard steering plate with this precision aluminum component for the most optimal steering attachment and greater rigidity. Contents include: - Steering Plate (x1)
- 3x14mm Cap Screw (x4)
- 6mm Ball Connector Nut (x2)
- 3mm Spring Washer (x2)
*Compatible Chassis: Nitrage 5.2
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Install these tough, lightweight, 4mm thick aluminum suspension plates, which are 1mm thicker than the standard parts, for greater part attachment precision and improved rigidity.
*Compatible Chassis: Nitrage 5.2
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Install these tough, lightweight, 4mm thick aluminum suspension plates, which are 1mm thicker than the standard parts, for greater part attachment precision and improved rigidity.
*Compatible Chassis: Nitrage 5.2
|
Install this universal propeller shaft to improve power transmission efficiency and reduce maintenance hassle. Please note that 2 sets of this Option Part are required to fully modify one vehicle. Contents include: - Swing Propeller Shaft (x1)
- Diff Joint Cup (x1)
- 2.5x14.8mm Shaft (x1)
- 4x4mm Grub Screw (x1)
- 5x5mm Grub Screw (x1)
- Cross Joint (x1)
- Anti-wear Grease (x1)
- 2mm Hex Wrench (x1)
- 2.5mm Hex Wrench (x1)
*Compatible Chassis: Nitrage 5.2
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
FRONT 5mm thick aluminum damper stay with extra attachment holes securely holds upper arms and dampers.
**Not for use with TNX 5.2R**
|
Install these universal drive shafts to improve power transmission efficiency and reduce maintenance hassle. Please note that 2 sets of this Option Part are required to fully modify one vehicle. Contents include: - Swing Drive Shaft (x2)
- Wheel Axle (R) (x1)
- Wheel Axle (L) (x1)
- 2.5x14.8mm Shaft (x2)
- 4x4mm Grub Screw (x2)
- Cross Joint (x2)
- Anti-wear Grease (x1)
- 2mm Hex Wrench (x1)
*Compatible Chassis: Nitrage 5.2
|
REAR 5mm thick aluminum damper stay with extra attachment holes. Securely holds upper arms and dampers.
**Not for use with TNX 5.2R**
|
|
|
